Problem with my network card and asterisknow

Get help with installing and running AsteriskNOW.

Moderators: Moderator, Support

Problem with my network card and asterisknow

Postby papini.sascha » Sun Jan 07, 2007 7:51 am

Hi all ... excusme for my english but I'm italian .... :D
I have one problem with my asterisknow and my server ... kernel disable my network interface ... and dont' work ...
My model of my server is this
BIOSTAR iDEQ 220K AMD 754 VIAK8M800 VGA
http://www.biostar.com.tw/products/barebone/ideq/220k/index.php3

this is my /proc/modules
nls_iso8859_1 3968 1 - Live 0xdca41000
nls_cp437 5632 1 - Live 0xdcbd0000
vfat 9088 1 - Live 0xdcbcc000
fat 40092 1 vfat, Live 0xdcba0000
usb_storage 60096 1 - Live 0xdcbde000
zttranscode 6152 0 - Live 0xdca24000
ipv6 192480 12 - Live 0xdcc77000
wcusb 17952 0 - Live 0xdca0f000
wctdm 33472 3 - Live 0xdcbac000
wcfxo 10912 0 - Live 0xdca1a000
wctdm24xxp 81216 0 - Live 0xdcbb7000
wcte11xp 23968 0 - Live 0xdcb99000
wct1xxp 13984 0 - Live 0xdca15000
wct4xxp 304960 0 - Live 0xdcbf2000
tor2 87328 0 - Live 0xdca27000
zaptel 190244 17 zttranscode,wcusb,wctdm,wcfxo,wctdm24xxp,wcte11xp,wct1xxp,wct4xxp,tor2, Live 0xdcb69000
binfmt_misc 7944 1 - Live 0xdca00000
dm_mod 43832 0 - Live 0xdca03000
video 13700 0 - Live 0xdc9ef000
button 5008 0 - Live 0xdc9e6000
battery 7556 0 - Live 0xdc9e3000
ac 3588 0 - Live 0xdc82a000
ohci1394 26416 0 - Live 0xdc9cf000
ieee1394 274228 1 ohci1394, Live 0xdcaa3000
uhci_hcd 17548 0 - Live 0xdc8d3000
ehci_hcd 24968 0 - Live 0xdc9c7000
hisax 388688 0 - Live 0xdca43000
crc_ccitt 1920 2 zaptel,hisax, Live 0xdc83e000
isdn 111072 1 hisax, Live 0xdc9aa000
slhc 5504 1 isdn, Live 0xdc892000
i2c_viapro 6676 0 - Live 0xdc8d0000
i2c_core 14736 1 i2c_viapro, Live 0xdc8cb000
snd_via82xx 20632 0 - Live 0xdc8f2000
gameport 10120 1 snd_via82xx, Live 0xdc8c7000
snd_ac97_codec 78880 1 snd_via82xx, Live 0xdc90d000
snd_ac97_bus 1920 1 snd_ac97_codec, Live 0xdc82c000
snd_pcm_oss 31104 0 - Live 0xdc8e9000
snd_mixer_oss 13824 1 snd_pcm_oss, Live 0xdc895000
snd_pcm 57864 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss, Live 0xdc8d9000
snd_timer 16644 1 snd_pcm, Live 0xdc8c1000
snd_page_alloc 7048 2 snd_via82xx,snd_pcm, Live 0xdc83b000
snd_mpu401_uart 5248 1 snd_via82xx, Live 0xdc838000
snd_rawmidi 17152 1 snd_mpu401_uart, Live 0xdc889000
snd_seq_device 5900 1 snd_rawmidi, Live 0xdc82e000
snd 39044 9 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device, Live 0xdc8b6000
soundcore 6496 1 snd, Live 0xdc81c000
8139too 19584 0 - Live 0xdc832000
mii 4352 1 8139too, Live 0xdc827000
floppy 49668 0 - Live 0xdc87b000
ext3 104072 2 - Live 0xdc89b000
jbd 40980 1 ext3, Live 0xdc86f000
sata_via 5508 3 - Live 0xdc81f000
libata 52620 1 sata_via, Live 0xdc861000
sd_mod 15120 6 - Live 0xdc822000


this is my dmesg
Linux version 2.6.17.11-1.1.x86.i686.cmov (conary.rpath.com@rpl:1) (gcc version 3.4.4) #1 Tue Sep 5 23:54:38 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bee0000 (usable)
BIOS-e820: 000000001bee0000 - 000000001bee3000 (ACPI NVS)
BIOS-e820: 000000001bee3000 - 000000001bef0000 (ACPI data)
BIOS-e820: 000000001bef0000 - 000000001bf00000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
446MB LOWMEM available.
On node 0 totalpages: 114400
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 110304 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 VIAK8M ) @ 0x000f7700
ACPI: RSDT (v001 VIAK8M AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bee3040
ACPI: FADT (v001 VIAK8M AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bee30c0
ACPI: MADT (v001 VIAK8M AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bee8400
ACPI: DSDT (v001 VIAK8M AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 20000000 (gap: 1bf00000:e2d00000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ quiet
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1800.134 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 448860k/457600k available (1847k kernel code, 8140k reserved, 746k data, 160k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3604.23 BogoMIPS (lpj=7208463)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Sempron(tm) Processor 3000+ stepping 02
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 0k freed
ACPI: setting ELCR to 0200 (from 0628)
checking if image is initramfs... it is
Freeing initrd memory: 974k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf9ff0, last bus=1
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Quirk-MSI-K8T Soundcard On
PCI: Unexpected Value in PCI-Register: no Change!
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 6 7 10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23), disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f4000000-f5ffffff
PREFETCH window: f0000000-f3ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1168176697.848:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 128M @ 0xe8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ 3
PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 3
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xe500-0xe507, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe508-0xe50f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: Hewlett-Packard CD-Writer Plus 9100b, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
SLPB PCI0 USB0 USB1 USB2 USB3 USB4 USB5 USB6 USB7 AC97 UAR1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 160k freed
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
sata_via 0000:00:0f.0: routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xEA00 ctl 0xE002 bmdma 0xE300 irq 10
ata2: SATA max UDMA/133 cmd 0xE100 ctl 0xE202 bmdma 0xE308 irq 10
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01 87:4763 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: SATA link down (SStatus 0)
scsi1 : sata_via
Vendor: ATA Model: HDS728080PLA380 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11

PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xd400, 00:e0:4c:e5:e7:18, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'

ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 10, io mem 0xf6012000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ 3
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 3, io base 0x0000e600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ 3
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 3, io base 0x0000e700
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 10, io base 0x0000e800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 10, io base 0x0000e900
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[f6010000-f60107ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
Using specific hotkey driver
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
EXT3 FS on sda3, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0030670000069c50]
Adding 1052248k swap on /dev/sda2. Priority:-1 extents:1 across:1052248k
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
irq 11: nobody cared (try booting with the "irqpoll" option)
<c01322c6> __report_bad_irq+0x2b/0x68 <c013238f> note_interrupt+0x73/0x98
<c0131ea1> __do_IRQ+0x68/0x8f <c0103db4> do_IRQ+0x42/0x4f
<c0102b86> common_interrupt+0x1a/0x20 <c0101043> default_idle+0x2b/0x53
<c01010bf> cpu_idle+0x40/0x5c <c038c618> start_kernel+0x184/0x186
handlers:
[<dc833aa2>] (rtl8139_interrupt+0x0/0x116 [8139too])
Disabling IRQ #11
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.4.0-beta3 Echo Canceller: MG2
Registered Tormenta2 PCI
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ 3
Freshmaker version: 73
Freshmaker passed register test
Module 0: Installed -- AUTO FXO (FCC mode)
Module 1: Installed -- AUTO FXO (FCC mode)
Module 2: Installed -- AUTO FXS/DPO
Module 3: Not installed
Found a Wildcard TDM: Wildcard TDM400P REV I (3 modules)
usbcore: registered new driver wcusb
Wildcard USB FXS Interface driver registered
Registered tone zone 0 (United States / North America)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NETDEV WATCHDOG: eth0: transmit timed out
eth0: no IPv6 routers present
Zaptel Transcoder support loaded
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 6 dirty entry 2.
eth0: Tx descriptor 0 is 0008a05a.
eth0: Tx descriptor 1 is 0008a04e.
eth0: Tx descriptor 2 is 0008a03c. (queue head)
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a046. (queue head)
eth0: Tx descriptor 1 is 0008a046.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
NETDEV WATCHDOG: eth0: transmit timed out
Vendor: USB 2.0 Model: Flash Disk Rev: 1100
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 506880 512-byte hdwr sectors (260 MB)
sdb: Write Protect is off
sdb: Mode Sense: 43 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 506880 512-byte hdwr sectors (260 MB)
sdb: Write Protect is off
sdb: Mode Sense: 43 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a05a. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a046.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 50.
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 0008a03c. (queue head)
eth0: Tx descriptor 1 is 0008a03c.
eth0: Tx descriptor 2 is 0008a03c.
eth0: Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out


can help me please
papini.sascha
Newsterisk
 
Posts: 3
Joined: Sun Dec 24, 2006 11:29 am

Postby j4m3s » Sun Jan 07, 2007 5:43 pm

papini.sascha wrote:eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
irq 11: nobody cared (try booting with the "irqpoll" option)
<c01322c6> __report_bad_irq+0x2b/0x68 <c013238f> note_interrupt+0x73/0x98
<c0131ea1> __do_IRQ+0x68/0x8f <c0103db4> do_IRQ+0x42/0x4f
<c0102b86> common_interrupt+0x1a/0x20 <c0101043> default_idle+0x2b/0x53
<c01010bf> cpu_idle+0x40/0x5c <c038c618> start_kernel+0x184/0x186
handlers:
[<dc833aa2>] (rtl8139_interrupt+0x0/0x116 [8139too])
Disabling IRQ #11


It appears as though something with that IRQ is bad. Try booting with the 'noapic' or 'irqpoll' options.
j4m3s
Oldsterisk
 
Posts: 249
Joined: Fri Dec 22, 2006 1:31 pm


Return to AsteriskNOW Support

Who is online

Users browsing this forum: No registered users and 1 guest